유니온백시멘트이미지

The completion of high class floor plastering (Self-leveling mortar)UNIFLOW I(Industrial), R(Reinforcing), T(Thickening)

UNIFLOW is self-leveling mortar that can level by itself and displays smooth and elegant surface enhancing crack resistance and delamination resistance.

  • 순백색 High strength
  • 수강성 Durability
  • 고강도 High liquidity
  • 고강도 Adhesiveness
  • 순백색 Crack binding strength
  • 수강성 Early strength
     
  • 고강도 Eco-friendly
     
     
  • 고강도 Versatility
INQUIRY
INQUIRY
닫기
Only for PRODUCT Belief to the best product

As pre-mixed type mortar with carefully selected cement, aggregates and special additives which are technically measured, it’s convenient to construct without other additives or supplementing liquid resin but only mixing with water. Also it can save the labor cost by handy construction and attributes to shorten the term of works as it significantly performs high early strength. UNIFLOW is readily available by anyone for high-quality precise construction.

  • High liquidity and high leveling (excellent smoothness and elegant floor plastering)
  • Outstanding early strength (smoothing next processes and getting the works term shortened)
  • Good workability (convenient and precise construction)
  • High strength and high durability (stable long-term strength)
  • High adhesiveness and no self-cracking
Only for TECHNOLOGYPrecise quality control via R&D
Product UNIFLOW (for Industry) I UNIFLOW (for Reinforcing) R UNIFLOW (for Thickness) T
Application
  • Floor for high durability in plant, logistics center
  • Floor for high durability in plant, logistics center, and parking lots of apartment and shopping mall
  • Exposed concrete finishing
  • Fancy interior floor for department store, shopping mall, café etc.
  • Excellent leveling for hospital, laboratory, studio etc.
  • Maintenance or repair (alteration of floor materials) and plastering finishing
  • Residential floor, balcony extension
  • Excellent leveling for replacing 40mm mortar
  • Maintenance or repair (alteration of floor materials) and plastering finishing
Flow 225mm(±5) 230mm(±5) 215mm(±5)
Compressive strength
(N/mm2)
34 31 31
Adhesive strength
(N/mm2)
1.8 1.8 1.6
Water ratio 21% 23% 21%
Use amount/1m2 1.6kg/mm,m2 1.6kg/mm,m2 1.7kg/mm,m2
Thickness 3~15mm 5~15mm 7~50mm
Instruction
  • ◆ Groundwork treatment
    • Have the floor smooth without irregularities and the base with adequate strength.
    • Get the floor dry and clean without paint, oil, grease or any other bonds.
    • Check the level by needs or divide the construction zone according to capacity. Use the proper amount measuring area and level state and determine thickness.
  • ◆ Primer applying
    • Apply PRIMER by two times – 1st application : dilute thrice and 2nd application : dilute twice. PRIMER prevents bubbling from the base absorption and increases adhesiveness.
  • ◆ Kneading and spreading
    • Kneading
      Knead UNIFLOW and water and mix it thoroughly without any lumps left.
    • spreading
      After pouring the mixed UNIFLOW, make it smooth on the floor with a pin roller or brush.
      In case of small area construction, a trowel can be used instead of a pin roller.
      Continuous spreading shall be done as prompt as possible within 20 min.
      2~3 times of pin roll works or trowelling are suitable and do not excessively work.
  • ◆ Curing and Finishing
    • Curing
      Do not place any materials on the floor for 24 hours after construction and protect it in proper conditions.
    • Finishing
      Additional finishing works shall be done after the self-leveling construction is completely dehydrated for additional construction.
Attention
  • Construct UNIFLOW after the base is fully cured (The water containing ratio of the base < 7%)
  • Works interval shall be within 10 min. and mind the boundary against slope.
  • Beforeㆍafter or on construction, prevent it from quick dehydration by windㆍheat or sunlight.
  • After UNIFLOW construction, additional works are highly recommended when the water containing ratio of the base is below 7%.
  • Please find the specifications for more details.
Only for PERFOMANCEBest performance for works convenient

  • Plant / logistics center - UNIFLOW I

  • Parking lot – UNIFLOW I

  • Exposed concrete finishing – UNIFLOW I

  • Exposed concrete finishing – UNIFLOW R

  • Commercial facilities – UNIFLOW T

  • Commercial facilities – UNIFLOW R

  • Hospital – UNIFLOW R