유니온메인페이지로가기
유니온백시멘트이미지

Strong adhesive powerPOWERMENT

POWERMENT is the standard type of tile adhesive mortar which figures optimal mixture of White Portland Cement, aggregates and high performance additives.

  • 우수한 처짐저항성 Excellent sagging-resistance
  • 작업성 Workability
  • 접착성 Adhesiveness
  • 친환경 건축자재 Eco-friendly construction material
INQUIRY
INQUIRY
닫기
Only for PRODUCT Belief to the best product

As it shows remarkable adhesiveness, delamination or cracking are not expected. With special resins and aggregates which are strictly screened, it achieves best-workability and cuts off construction period on excellent effectiveness.

  • Robust adhesion
  • Optimal mixture with additives
  • Exceptional workability and efficiency
  • Excellent sagging resistance
Only for PERFORMANCEBest performance for works convenient
Specification
Product POWERMENT
Color White powder
Working hours 40 min
Open time 10 min
Main composition White Portland Cement, Fine aggregates, Additives
Standard amount 4.8~5.3kg/m2(by compression method with 7mm-uneven trowel)
Package 20kg/25kg in sack
Curing time Gait on Day 7th / Curing on Day 28th
Mixture 5.6±0.4ℓ/25kg
Construction temperature 10~25℃
Best valid for 3 months

* Use amount can be differentiated by floor condition.

Application
  • •Exterior : Adhesion of semi-porcelain tile, stoneware tile, artificial stones & other stones.
  • •Interior : Adhesion of porcelain tile, artificial stones.
  • •Porcelain tile size under 300mm x 300mm.
Instruction
  • 1. Groundwork treatment
    • •The surface of concrete or mortar shall be fully cured.
    • •Remove all irregularities and flatten the surface of the base.
    • •Remove all pollutants like dust, oil, paint etc.
    • •Adjust the surface of super-absorbent base (such as ALC) with primer.
  • 2. Mixture
    • •Mix POWERMENT 25kg with 5.6±0.4ℓ of water by hand-mixer sufficiently for at least 3 min. to prevent lumps.
    • •Use the mixed mortar within 40 min.
  • 3. Tile installation
    • •Work with mixed adhesive approx. 7mm thickness by uneven trowel on the surface of the base.
    • •Attach tiles to the surface within 10 min.(standard situation) as it may be incomplete adhesion.
    • •Attach tiles twisting and beat lightly with rubber hammer in order for the adhesive surface to be covered with adhesion more than 80%.
  • 4. Cleaning and curing
    • •Clean out the adhesive on the surface of tiles before hardened.
    • •After the completion of works, any impact, freezing or water contact are prohibited before it is fully hardened.
    • •Work joint construction in 7 days after adhesion.
파워멘트1 파워멘트2 파워멘트3
Attention
  • •Construct it above 5℃ of the surface of the base.
  • •Do not construct it on ceramic tile, polishing tile or tiles with absorptivity less than 1%.
  • •Construct with 3mm joint gap considering expansion & contraction of the base & tiles in order to prevent tile lifting.
  • •Mind that it causes discoloring of joint or tile falling-off in case joint construction is done before the adhesive is fully cured.
  • •Prohibit any impacts, freezing, and water contact during curing. (tile falling-off caused)
  • •Mind the working hours can be differentiated by work-site circumstances. (temperature or wind)
  • •Store it in well-ventilated and dry in-house condition. Dry storage by in-house condition is a must against spoilage and use within 3 months.
  • •If other purposes desired, please contact our R&D department.